1988 MX-6 GT 5 speed White/ Burgundy interior 1988 MX-6 GT 5 speed White/ Blue interior 2005 Dodge Ram 3500 Cummins Quad Cab 4x4 2003 Dodge Caravan 3.3 V6. 1.8L V6 TO 2.5L V6 ENGINE SWAP LINKS AND INFO . (Mazda 626 & MX-6) - 1998+. MX-6's with A Manual Transmission. Auto to Manual swap. So I. but it is labeled in the diagram Manual trans/auto trans. MIATA MX-5 FORUMS. MAZDA NEWS ROOM; NA. Mazda 6 Forums : Mazda 6 Forum / Mazda Atenza Forum. (Atenza) > Newbie Section > auto to manual swap User Tag List. you CAN swap to manual.
HOW- TO: Tranny swap - Probe. Talk. com Forums.
Mazda Mx6 Auto To Manual Swap Honda
Automatic to 5 speed swap. Mazda claims about 10 less horsepower for the auto engine. Still, the swap is fairly. a manual Miata and swap all the pieces.
Shifter installation and removal. Get inside car and get ready to out atx shifter. Atx shifter cable- 1. As the shifter lock stops you from turning off the car when in gear. And the cable is loose. You wont be able to turn your key off and pull out. To solve that, trace that cable to the key hole.
. the car is a 1988 mazda mx6 and manual trans. 1G MX6 General > Help!!! auto 2 manual swap, cpu. what do all the cpu's do and do i need to swap them.
Automatic To Manual Conversion. John Seegers JESFromRIC. Impact 6 points. ECU the auto ECU will *kind of * work. Want to watch this again later? Sign in to add this video to a playlist. MX6 Manual Transmission Fluid Change.
Pull on the cable. Youll see why it wont hold. Pull the cable, you can turn and take the keys out, cable in, cant take out. I ghetto rigged it with some rubber bands so itll hold in place. Install mtx shifter and rod. Go underneath car and unbolt the cat, 4 1.
Push the mtx shifter assembly through the hole. Other person inside car bolts on the shifter, 4 1. Bolt shifter rod to tranny. There should be 2 rods. One for shifting and one for vibration dampening. Bolt on cat. Again. Make sure gasket is tight.
Get inside car, you should be able to shift into every gear. Dont do too much ass the tranny doesnt have gear oil. Install your shift knob on there. Install the shift boot onto shifter panel. Put back the panels inside the interior. Shifter panel, center console, steering wheel and column panels. Plug the hose from clutch master cylinder to the fluid reservoir - attach clutch line onto clutch master cylinder 1.
Use box wrench for lines - There should be 2 clutch lines and 1 clutch hose. If you want, buy rr ss clutch line and replace clutch hose with that. Itll run under the top tranny mount.
And onto the bracket that is attached to the tranny mount. The clutch hose should attach to that and the other end of clutch hose on the tranny. From the clutch hose is another clutch line that goes to the clutch slave cylinder. Attach onto slave cylinder, 1. The slave cylinder should be on the tranny already. The slave cylinder is on top of the front engine mount.
It should be against the fork. Be sure to put high temp grease on each end of the axle to get the axle into tranny and hub smoothly. Install steering rod, 1. Install new cotter pin onto the nut - Install hub onto strut. Install (*if applicable) abs bracket and abs sensor(2 1. Do the same to the passenger side, with the addition of intermediate shaft and carrier bearing.
Install transverse member 6 1. Install crossmemer 2 1. Install the tranny to crossmember rubber isolator 2 1. Install to front chassis and front engine mount. Along with the pads and brake lines of course. Tighten down axle nut onto axle.
Tap the edge of nut into the notch in the axle. Be sure to use locktite to be safe. You don't want a axle poppingout on you during driving. Bleed brake and clutch. Bleed brakes first.
Make sure you use a power brake bleeder, you will need it as there is too much air in the line for you to do it manually. Go to www. motiveproducts. Reinstall splash guards. Put wheel back onto hubs.
Lower car. Electrical - Plug in harnesses in tranny area. Plug in vehicle speed sensor. Dont plug in reverse light switch.
To resolve that, use the 2 wires from the reverse light switch, plug into the to the 1 and 4 for continuity( for the harness in the illustraion below) - Use 2 wires and jump 6 and 9 to trick the comp, so you can start the car. The orange harness that looks like this: TOP - -- -- -- -- -- - |1 2 3 4 5| |6 7 _ 8 9| - -- -- -- -- -- BOTTOM Reinstall other stuff: - Fill up tranny gear oil - Cruise control, charcoal canister, battery, intake. Start car and drive!!!
Remember clutch break in period of 5. This write- up is copyrighted by Chunchoy. M(y)x. 6gr. 8ride. Any unauthorized use will be prohibited without the written consent of us. Just give the credit if you use it. Mazda Mx- 6 M- edition- New Toy! Looking for a replacement engine.